Understanding HSI part numbers - Haydon Switch & Instrument - A Tritex Corporation Company, motor's series, motor's step angle, number of leads, leadscrew, travel per step

Name:
E-mail:

	Size 14 with Integrated Connector
	New Linear Rail Systems
	New Size 11 Double Stack Captive Hybrid Linear Actuator

UNDERSTANDING CANSTACK PART NUMBERS

Printable Page

Email This Page

< Back to Haydon Resources

A standard Haydon motor part number consists of 7 digits to 10 digits – XXXXX-VV.
(Excluding 15000 SeriesMotors). The digits represent:

The first and second digits indicate the motor's series or diameter (in mm).
	Example: 26000 Series = 26 mm diameter
The third digit indicates the motor's step angle (see Salient Characteristics tables)
	Not all step increments are available for every frame size. See each motor listing for step increments that are available for a given frame size.
The fourth digit indicates the number of leads
	4 leads - bipolar 6 leads - unipolar
The fifth digit indicates the pitch of the leadscrew or the travel per step
	(see Selector Chart Code Letters or Code Digits) Note: When ordering Rotary Motors this digit is always "0"
The sixth and seventh digits indicate the motor's voltage. Standard voltages are 5 (05) and 12 (12) volt. Custom voltages are available.
PREFIX Codes positioned before the part number designate specialty requirements. All options listed below may not be applicable to all motors. Please see individual motor listings for available options.
	E = Prefix used when requesting External Linear Motors LC = Prefix used to indicate 15000 Series motor P = Prefix indicating Proximity Sensor S = Prefix indicating Home Position Switch T = Prefix indicating High Temperature option
SUFFIX Codes: -999 positioned after the part number indicates Rotary motors with BALL BEARINGS. -900 denotes standard external motor with greaseand flanged nut. For assistance with building a part number or with a custom design, please contact our sales department.

SCREW LENGTH OPTIONS: For non-captive shaft and external linear shaft motors various screw lengthsare available to accommodate any travel requirement.

HSI CANSTACK LINEAR ACTUATORS: STEP MOVEMENT SELECTOR CHART

Travel Per Step Code Letter or Digit	Linear Travel Per Step		15000¹ Series Ø 15 mm (0.59")	20000 Series Ø 20 mm (0.79")	26000 Series Ø 26 mm (1.0")	36000 Series Ø 36 mm (1.4")	46000 Series Ø 46 mm (1.8")	Z20000 Series Ø 20 mm (0.79")	Z26000 Series Ø 26 mm (1.0")
Travel Per Step Code Letter or Digit	Inches	Millimeters	Screw Ø 5 mm (0.197")	Screw Ø 3.56 mm (0.140")	Screw Ø 3.56 mm 0.140")	Screw Ø 3.56 mm (0.140")	Screw Ø 5.54 mm (0.218")	Screw Ø 3.30 mm (0.130")	Screw Ø 3.30 mm (0.130")
7	0.000125*	0.0032*				•
9	0.00025*	0.0064*			•	•
3	0.0005	0.013			•	•	•		•
W	0.00079	0.02	•
1	0.001	0.0254		•	•	•	•	•	•
AS	0.00164	0.04166							•
2	0.002	0.051		•	•	•	•	•	•
4	0.004	0.102		•	•	•	•	•	•
8	0.008	0.203					•
G	0.016	0.406					•

* Specialty and high resolution step movements.

¹ The 15000 Series is currently available with captive screw only.

Site Support by:
Progressive Software Solutions